Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
We have come across this great article pertaining to Tools You Need to Install a New Bathtub down the page on the web and decided it made perfect sense to relate it with you on this page.
Installing a bathtub isn't exactly rocket science, but it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the project can move speedily; if you have to open a wall to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old tub and set in the brand-new one. See to it you have actually certified yourself for the task and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will aid you mount a brand-new bathtub in your bathroom if you have actually currently gotten a brand-new tub as well as do not require to change the arrangement of your previous water pipes.
Your devices and material list ought to comprise the following:
Preparing for the Installment
First of all, the supporting structure supplied with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bathtub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and tighten them if required. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the tub must wait up until the bathtub has been made use of at least when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap as well as the sink. Protect the tap in place with the producer supplied backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type ought to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about complications with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to permit the motion experienced when the tub is in use. The sealer can split relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post about Tools You Need to Install a New Bathtub . Thanks for taking the time to browse our piece. Liked our piece of writing? Please share it. Help someone else check it out. I cherish reading our article about How to Install a Bathtub Yourself.
Source This Article Report this page